ac-dc specification 150 watts 3?x 5?footprint fits 1u applications convection-cooled open frame & u-channel versions optional power fail detect signal optional low temperature operation up to 90% efficiency SDS150 series input input voltage 90-264 vac (120-370 vdc) input frequency 47-63 hz input current 2.0 a at 115 vac 1.0 a at 230 vac inrush current 20 a at 115 vac 63 a at 230 vac power factor >0.95 earth leakage current <0.40 ma at 115 vac <0.75 ma at 230 vac input protection 3.15 a on board fuse output output voltage see table output voltage trim ?% initial set accuracy 1% minimum load no minimum load required start up delay 2 s max start up rise time 2 ms typical hold up time >16 ms line regulation 1% max, ?.5% typical load regulation 5% max, ?.0% typical transient response 4% max deviation, recovery to within 1% in 500 ? for a 50% load change ripple & noise 1% pk-pk max overvoltage protection 112-132%, recycle input to reset overload protection 110-150% with auto recovery short circuit protection trip & restart (hiccup mode), auto recovery temperature 0.04%/ c coefficient xppower.com general efficiency 88% typical, 90% max isolation 3000 vac input to output 1500 vac input to ground 500 vdc output to ground switching frequency pwm 60 khz typical, pfc 100 khz typical power density 6.9 w/in 3 for open frame version signals power fail detect = ttl low (option) mtbf >100 khrs per mil-hdbk-217f environmental operating temperature 0 ? to +70 ?, derate linearly from 100% load at +50 ? to 50% load at +70 ?, low temperature option ?l?-40 ? cooling convection-cooled operating humidity 5-95% rh, non-condensing storage temperature -40 ? to +85 ? vibration 2 g on 3 axes emc & safety emissions en55022, fcc part 15, level b conducted harmonic currents en61000-3-2 voltage flicker en61000-3-3 esd immunity en61000-4-2, level 2 perf criteria a radiated immunity en61000-4-3, 3 v/m perf criteria a eft/burst en61000-4-4, level 2 perf criteria a surge en61000-4-5, level 3 perf criteria a conducted immunity en61000-4-6, level 2 perf criteria a dips & interruptions en61000-4-11, 70% u t for 10 ms, 40% u t for 100 ms, <5% u t for 5000 ms perf criteria a, b, b safety approvals en60950-1, ul60950-1, csa60950-1 per cul, ce mark lvd
22-jun-07 ac-dc 1.62 (41.2) 1.18 (30.0) 3.90 (99.06) 2.57 (65.3) 0.55 (14.0) 5.00 (127.0) 4.50 (114.3) 4.00 (101.6) 0.25 (6.4) 3.21 (81.5) 0.25 (6.4) 45.0 (114.3) 1.18 (30.0) pitch = 3.96 mm 0.54 (13.6) 0.67 (16.9) m3* p0.5 (mounting holes) x 4 pfd m3* p0.5 (mounting holes) x 5 input ac p2 p1 dc output 13 1 g n l adj ?4.0 (mounting holes) x 4 1.40 (35.6) 3.00 (76.2) 4.55 (115.6) 5.00 (127.0) 0.32 (7.9) 3.00 (76.2) 0.22 (5.5) 0.43 (10.9) 0.56 (14.2) 0.22 (5.7) 2.57 (65.3) 0.12 (3.0) 0.80 (20.3) 1.21 (30.7) 1.16 (29.6) 1.16 (29.6) 0.80 (20.3) 1.57 (40.0) m3 x p0.5 (mounting holes) x 4 pitch = 3.96 mm pfd ac input p2 p1 dc output 1 p2 p1 g n l 13 SDS150 mechanical details p2 - pin connections pin function pin function 1 v1 7 return 2 v1 8 return 3 v1 9 return 4 v1 10 return 5 v1 11 return 6 v1 12 return 13 pfd (2) models and ratings maximum output power output voltage output current total regulation (1) model number (2,4,5,6) minimum maximum 144 w 9 v 0 a 16.00 a 5% SDS150ps09b ?^ 150 w 12 v 0 a 12.50 a 5% SDS150ps12b ?^ 150 w 15 v 0 a 10.00 a 5% SDS150ps15b ?^ 150 w 18 v 0 a 8.33 a 4% SDS150ps18b ?^ 150 w 24 v 0 a 6.25 a 3% SDS150ps24b ?^ 150 w 30 v 0 a 5.00 a 2% SDS150ps30b 150 w 36 v 0 a 4.17 a 2% SDS150ps36b 150 w 48 v 0 a 3.13 a 2% SDS150ps48b ?^ notes open frame u channel 1. total regulation includes initial set accuracy, line regulation and load regulation. 2. for optional 2 pin molex input, add suffix ?d?to model number. example SDS150ps12-d. 3. for non-standard voltages contact sales office. 4. for optional power fail detect signal (pfd), add suffix ?p?to model number . example: SDS150ps48b-p. 5. for optional pcb only version, delete suffix ??from model number. example SDS150ps48. 6. for optional low temperature operation, add suffix ?l?to model number. example: SDS150ps12-l notes: 1. dimensions in inches (mm), tolerance ?.02 (?.5). 2. optional power fail detect signal on ??versions only. standard models have no connection for pin 13. 3. input connector p1 mates with molex housing 09-50-3051 and molex 2478 series crimp terminal. 4. output connector p2 mates with molex housing 09-50-3131 and molex 2478 series crimp terminal. 5. for mating connector kit order part number sds120 con kit. 6. for cable harness order part number sds120s loom. 7. din clips are available for alternate mounting order 2 x ?in clip? 8. for optional cover kit order part number SDS150 cover. to receive unit with cover fitted add suffix ?c?to model number. height increases by 0.18 (4.5). pfd is +5 v for normal operation. source current is 5 ma max. pfd is <0.4 v for either ac fail (<90 vac) or dc fail (<95% vnom). sink current is 10 ma max. all dimensions are in inches (mm) tolerance: ?.02 (?.5) weight: 1.23 lbs (560 g) approx. +5 v pin 13 internal power fail detect ? available from farnell. see pages 204-206. ^ available from newark. see pages 207-208.
|
